12_ #s maybe - hope I can narrow that down), the program resumed loading and working. Even more telling perhaps is that the 2 or 3 times I reverted all the MakeMKV program files back to whatever that previous version was (in the ver. If access to or use of the external BR drive was compromised, one would not expect other programs that use it to work either, yet they do. (Some of them were Mac users.) I'm going to check on the JRE angle, which one user reported. and apparently many have run into this error over the last few years, although under varying circumstances. of the links in post #7 appears more relevant to me. Where did I go wrong, and how to correct this ? I managed to put the older files back into the original program folder instead, and this seemed to accept the latest temp key. Huh ? So, I was left with NO MakeMKV at all. Never got to where you apply the temporary key, because the program keeps saying that it encountered a fatal error and must terminate. The 1.14.4 install complained that the folder was not empty, so I moved those files out to a backup location elsewhere, then tried to redo the install. This time I tried to uninstall the previous version first, which looked to have worked, but then it turned out that there were some files left over in the MakeMKV directory. Can't recall offhand whether this was done over top of the previous version. Looks like MakeMKV have issue reading the disc.I've done this several times in the past without a problem, until just now with the latest release 1.14.4. So you are ripping using the GUI ? I don't think that the issue is related to the fact your are accessing the UI from different locations. I am using an LG WH16NS60 in an external USB enclosure. I will post logs tomorrow, after i test again to verify.Įdit: I have tested using a 4K bluray and have attached the logs from the newly created docker. I have to remove the container and then add it back to Unraid to start another manual rip. The restart circles for a few minutes and then goes back to started and then the webui does not ever connect again. I am also having an issue where i cannot restart the docker. The copy stops and the remaining time climbs infinitely. I am having an issue with the manual rip of a movie, that if i try and monitor the progress of the rip, from a different device than what i started it on. But in your scenario, the error is harmless (see and ). Currently, the automatic disc ripper stops for any scsi error (message code 2003). Then "Decrypting data", and proceeds to "Saving all titles". More PRGV and MSG records (either "too short" or "added" messages). MSG:3007,0,0,"Using direct disc access mode","Using direct disc access mode" After that, it shows all of the DRV records, then stuff like this: Are you getting the error a single time ? What is the message just after the error ?Ī single time, with each disc. There's a lot more, but I don't think it's very useful? MSG:2003,0,3,"Error 'Scsi error - ILLEGAL REQUEST:READ OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION' occurred while reading 'DVD+R-DL ATAPI DVD A DH16AASH SA15' at offset '1048576'","Error '%1' occurred while reading '%2' at offset '%3'","Scsi error - ILLEGAL REQUEST:READ OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION","DVD+R-DL ATAPI DVD A DH16AASH SA15","1048576"ĭRV:0,2,999,1,"DVD+R-DL ATAPI DVD A DH16AASH SA15","ROBIN_HOOD_S1_D1","/dev/sr1" I mean it does complain, but it doesn't immediately eject the disk and give up. opt/makemkv/bin/makemkvcon -r -cache=1 info disc:9999 If you don't know the disc ID, you can run: Container is gone now.Ĭould you try to rip the disc manually and provide the output ?Įnv HOME=/config /opt/makemkv/bin/makemkvcon -r -progress=-same mkv disc:0 all /output/manual_rip_test Is there a safe way to stop it from the command line? My other dockers are working fine (ie responding to restart and stop commands) and the container log just says there's no log because docker is marked for removal.Įdit: Docker became unresponsive so I had to stop and start the array. I'd reboot the server but I'm in the middle of a preclear. Finally tried to remove it and it's completely unresponsive. In my case, I just installed it, went to the webgui, no response, tried to restart then stop it, no response so I tried to edit it and same. Having a similar issue with this container. I can't make the docker stop or restart itself. The docker hangs and will not stop or restart when using the Unraid GUI. I have used the docker to rip about a dozen Blu Rays over several weeks, but over the last 3 weeks or so every rip requires an unclean (hold power button) shutdown before I can rip a second. Does anyone have any additional input on this issue?
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |